318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Maintenance

Notices

Maintenance Service Interval questions, oil change info.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Replies, 95,369 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Replies, 58,256 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Replies, 55,739 Views
M50+manual swap bastard...
03-01-2024 11:00 PM
Last post by Andy318
03-18-2024 02:34 PM
3 Replies, 130,531 Views
Reply Share/Bookmark
 
Thread Tools Display Modes
Old 01-22-2017, 09:37 PM   #1
Haunted_Smores
Junior Member
 
Join Date: Jun 2016
Location: America
Posts: 8
iTrader: (0)
Default Gametime: Where is the coolant coming from?

Ever since I've owned this car, it's been leaking coolant from every orifice. I've replaced many cooling parts, including the thermostat housing, radiator, various hoses etc. My original fear was that I had a head gasket leak due to the sheer amount I'd lose. (It's slightly more manageable now at about 1/2 the reservoir every 800 miles) And now looking at the block, my only assumptions at this point are that it's either an outer head gasket failure, or timing case gasket leak. Attached are some images, opinions would be very much appreciated.

http://imgur.com/vzVzAAQ

The engine bay. Coolant will pile up in the little space below between the a/c pulley, and the water pump pulley.

http://imgur.com/2Kqsa6j

An upward shot at what I believe is the head gasket. Is all that buildup carbon/oil, or coolant? Whatever it is seems to slightly leak from the gasket.

http://imgur.com/4L03g95

An even lower shot. This weird buildup is all over down here.

Any help would be soooo amazing.
Haunted_Smores is offline   Reply With Quote
Old 01-23-2017, 03:20 AM   #2
BRADESTAR
Senior Member
 
Join Date: May 2013
Location: Seattle
Posts: 513
Vehicles
iTrader: (0)
Default

Doze pictures don't do a whole lot for me. Can't tell what's what. If your oil and coolant are clean then you can borrow a coolant pressure test deal from O'riely's or autozone or the like. Clean it up, put pressure in there an you should see where it is coming from.
BRADESTAR is offline   Reply With Quote
Old 01-23-2017, 06:53 AM   #3
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 233
iTrader: (0)
Default

I'd say you need to do some cleaning and remove all those plastic shields from underneath, so you can get a good look. The last picture shows oil leaking above the split in the timing chain covers. could be the valve cover gasket or upper timing cover gasket. I've been chasing oil leaks on my 'ti for probably a decade now. You'll either need to do some good cleaning/detective work, or just tear into the engine and tackle them all at once. The coolant leak shouldn't be hard to find, especially if it's enough to pool up. How many miles?
paul somlo is offline   Reply With Quote
Old 01-23-2017, 07:04 AM   #4
Haunted_Smores
Junior Member
 
Join Date: Jun 2016
Location: America
Posts: 8
iTrader: (0)
Default

That's probably my best bet, since it is pretty dirty the further down you go. It's got about 183k on it. I got it around 20k miles ago and have been loving it to pieces. Its just cost me more than I'd like to admit, but it's easily worth it, plus I sort of knew what I was getting myself into. What are some good methods for cleaning surfaces like this? I'd imagine just get a wet rag or something and go to town.
Haunted_Smores is offline   Reply With Quote
Old 01-23-2017, 10:37 PM   #5
paul somlo
Senior Member
 
Join Date: Sep 2006
Location: Greeley CO
Posts: 233
iTrader: (0)
Default

Quote:
Originally Posted by Haunted_Smores View Post
What are some good methods for cleaning surfaces like this? I'd imagine just get a wet rag or something and go to town.
I've been using the Autozone house brand of engine degreaser - cheap, safe on plastics, and it doesn't evaporate immediately. Put some cardboard and a large towel that you're not fond of underneath, put on some gloves, and use a rag. You can follow up with something water based like Simple Green, then rinse with water.

Expect the coolant leak to be easy, the oil leaks not so much. There's lot's of DIY out there for both. Regarding oil, the most likely culprits are the valve cover gasket, the oil filter housing, the profile gasket between upper and lower timing cover, the profile gasket between the lower chain case and the head, and the oil pan gasket. The front and rear main seals are good for a long time and other than the head gasket, the other gaskets are embossed metal, and I don't think they wear readily.

You might try an inspection mirror and flashlight for the coolant that's pooling; you'll be able to see the underside of the water pump and thermostat areas a little better.

Paul
paul somlo is offline   Reply With Quote
Reply

Bookmarks

Tags
318ti , coolant , coolant leak , m44


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Overheating 202 Romoser.MD Engine 18 02-17-2011 09:23 PM
95 318ti coolant issue colacan Engine 2 11-03-2010 03:38 AM
New Tstat, Leaking Coolant, No Heat, Overheating Problem!! Please HELP! aziankingz HVAC 2 12-10-2009 04:39 PM
Disappearing coolant after overheating = blown head gasket? Eric Engine 22 08-09-2009 07:28 PM
Black Coolant adamud Engine 13 11-20-2007 02:49 AM


All times are GMT +1. The time now is 09:09 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
© vBadvanced CMPS v3.2.2
[page compression: 77.10 k/89.66 k (14.00%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.