318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base

Notices

Knowledge Base How to articles and things explained.

.
» Recent Threads
Need Help - ignition...
11-03-2013 06:09 AM
Last post by paul somlo
Today 03:41 AM
2 Comments, 565 Views
TX: 97 318TI covered in...
Yesterday 11:02 PM
Last post by E30-M3
Today 01:49 AM
3 Comments, 92 Views
CenCoast CA: Trade...
Today 01:10 AM
Last post by Strawman
Today 01:10 AM
0 Comments, 70 Views
1995 318ti slicktop
12-15-2014 06:32 AM
Last post by projekt EPiK
Yesterday 07:03 PM
7 Comments, 4,166 Views
318is dials into 318ti
08-16-2017 08:29 AM
Last post by zoner
08-17-2017 06:00 PM
8 Comments, 513 Views
Happy Birthday ...
08-17-2017 05:00 AM
Last post by 1996 328ti
08-17-2017 05:00 AM
0 Comments, 162 Views
m50swappp help
08-17-2017 03:49 AM
Last post by topless240
08-17-2017 03:49 AM
0 Comments, 94 Views
Worth Fixing?
08-09-2017 07:37 PM
Last post by cmurthi
08-17-2017 02:11 AM
4 Comments, 404 Views
318ti Sports
08-15-2017 12:48 PM
Last post by E30-M3
08-16-2017 09:42 PM
7 Comments, 413 Views
.
08-16-2017 06:49 PM
Last post by 96alaskanblue
08-16-2017 06:49 PM
0 Comments, 132 Views
Comment Share/Bookmark
 
Tutorial Tools Display Modes
Old 02-20-2005, 05:20 AM  
e30fiend
Junior Member
 
e30fiend's Avatar
 
Join Date: Nov 2004
Location: Seattle
Posts: 19
iTrader: (0)
Default How to change 318ti rear speakers (write-up with pictures!)

How to change the rear speakers in a 318ti

By Eric Miller

As you probably know, the rear speakers in a BMW 318ti are not a standard size. The only aftermarket speakers that fit without modification are MB Quartz (size 4T), there...

Last edited by e30fiend; 10-08-2012 at 11:17 PM.
e30fiend is offline   Reply With Quote
  #45  
By R111S on 07-09-2013, 03:03 AM
Default Installed Blaupunkt 4x6 GTx-462 DE Speakers in the rear

The rear Polk 4 Inch DB401 Speakers didn't last long so I put in Blaupunkt 4x6 GTx-462 DE Speakers. I paid $42.99 plus shipping from Amazon. They're rated at 35 Watts RMS (160 Watts Peak) and have a better Frequency Response of 80 Hz to 22 kHz.

I decided to mount the speakers flat against the Grill. I cut the old mounts for the 4inch units and used them to secure the 4x6 units across the longest dimension of the rear opening. I then sealed the air gaps using cut pieces of Corrugated Plastic (old Garage Sale Sign) secured with Goop Adhesive. I suspect the Voice Coils may last longer due to the flat mounting versus the angled OEM mounts. The Blaupunkts sound better than the Polk Speakers probably due to the better frequency response and higher peak power handling capability.
Reply With Quote
  #46  
By MrBonkers on 08-08-2013, 09:27 PM
Default

Thanks for the write up this will be coming in handy within the next few months. My drivers side sounds like garbage now. Thank you.
Reply With Quote
  #47  
By John Nicholson on 05-30-2014, 04:35 AM
Default

I didn't see this write up before doing mine so my dyi is a bit different. I had some 4 inch speakers laying around from a different project, they were 2 way speakers, a woofer only 4 inch would have been preferable.\
\
Of course you have to remove the carpet kit from the rear first, if you have the cd changer that needs to come out as well. On the right side there is the latch cable for the fuel fill door so you just need to move the carpet out of the way.\
\
Remove the 4 screws that hold the speaker assembly.\
\
Clip the wires off to the woofer or de solder, if you have the 10 speaker version like mine, it's likely your tweeters are fine\
\
Now look at the picture in the first post. Instead of trying to pry apart the glue holding the speaker to the speaker tube, I cut off the radials of the speaker itself so that they are flush to the diameter of the speaker. Note: you will mount the new speaker directly to the outer ring remnants of the old speaker.\
\
Now trim where you cut the radials so you have a smooth circle.\
\
Mount the new speakers, if done properly it should snap in flush.\
\
Bend the tabs for the screws upward so parallel with speaker tube, put some screws in and re solder the wires to new speakers.\
\
This method has the advantage of still using the OEM speaker tube as intended.
Last edited by John Nicholson; 05-30-2014 at 10:55 PM..
Reply With Quote
  #48  
By 98318ti on 06-29-2015, 11:53 PM
Default

I just used this thread to replace a speaker and thought I would update it with what I did.

1. After breaking the glue loose you can rotate the speaker with a little careful pressure from a long screwdriver. The you can carefully pry the speaker up.

2. Found some speakers that were as close to the right size as possible.

3. Used a dremel and exacto knife to cut slots out in speaker cone where the original slots were.

4. Insert speaker in slots and used some black silicone to secure it

I will let you know how it sounds, but it has to better than the blown speaker in there now.
Attached Images
File Type: jpg 053.jpg (61.4 KB, 29 views)
File Type: jpg 054.jpg (58.8 KB, 25 views)
File Type: jpg 055.jpg (38.2 KB, 26 views)
File Type: jpg 056.jpg (63.6 KB, 27 views)
File Type: jpg 058.jpg (71.1 KB, 25 views)
Reply With Quote
Comment

Bookmarks


Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
 
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT +1. The time now is 08:39 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2017, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 71.73 k/87.79 k (18.30%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.