318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base

Notices

Knowledge Base How to articles and things explained.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Comments, 99,085 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Comments, 62,014 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Comments, 59,286 Views
Comment Share/Bookmark
 
Tutorial Tools Display Modes
DIY - How to install an E36 X-Brace on your TI
DIY - How to install an E36 X-Brace on your TI
A nice suspension upgrade for a low price
Published by BlackBMWs
01-20-2015
Default DIY - How to install an E36 X-Brace on your TI

I have done a few of these on my TI's and have not really found a DIY on this easy upgrade.



I have found my E36 X-braces by watching the Pick & Pull for E36 convertibles or Z3s and getting out there quickly. I have a impact wrench, 13 and 16mm sockets, rag and garbage bag I use for those retrievals.



For this simple DIY you will need:



Installation:
  • An E36 X-Brace
  • 6 BMW Nutserts PN# 51718175003
  • 6 M8 25mm bolts
  • 6 M8 washers



Tools:
  • 6 M8 1.50 Allen bolts (or regular M8 hex bolts)
  • 6 M8 nuts
  • 12 M8 washers
  • Red Loctite
  • 10mm open or ratcheting wrench
  • 8mm Allen socket and ratchet (or wrench if you are using a hex bolt
  • 13, 16mm sockets and ratchet/breaker bar
  • Ramps or stands
  • Floorjack
  • A file or rotary rasp to elongate the X-brace holes if needed
  • Handlight



An hour of time.



---------------------------------------------------------------------

Preperation:

Clean typically greasy X-brace

Prep the six compression nuts (Nutserts) for installation.





I did mine shortly after taking this shot. If you have time for the Loctite red to harden, use way less. I prepped these the hour of the install. In retrospect, I'd use half the amount of Loctite next time around. Two of the six bolts locked up pretty well. Four of the bolts released just fine.





Installation:
  • Raise up front and chock rear tires.
  • Remove the lower plastic underpan if you have one installed
  • Using the 16mm socket and breaker bar, remove existing cross brace.







A light coat on the Nutsert to help it not spin after installation.





Updated procedure: Tap the Nutserts into the front subframe. The holes are slightly smaller than the Nutserts. I used a mini 2 lb sledge I got from Harbor Freight to tap all six in. (I forgot to take a pic. )



Tighten the nut, not the Allen bolt. Make sure it's on tight, so the Nutsert won't spin. When the nut stops, you've crushed the Nutsert sufficiently. Reverse and extract the allen bolt.







Install the X-brace with the M8 bolts and washers on the subframe and the big bolts from the original subframe bar. I had to elongate the holes on the frame bar 1/8" to get the frame crossbar bolts to go in straight on one of the installations. I had to improvise with the bolts 5&6 (Center) with spares from the bolt bin.

The center Nutserts are used to secure the M undershield if you choose to use one. You actually only need four to secure the X-brace to the subframe.




Lower car, test drive and enjoy!
Tutorial Tools

  #1  
By eurohb on 01-20-2015, 09:24 PM
Default

Thank you! I will be doing this soon to my Ti so that i don't hurt the undercarriage !
Reply With Quote
  #2  
By mnguyen84 on 09-07-2017, 02:10 AM
Default

pictures are broken D:
Reply With Quote
  #3  
By BlackBMWs on 09-07-2017, 06:50 AM
Default

Yes, thank Photobucket.


Sent from my iPhone using Tapatalk
Reply With Quote
  #4  
By 740isport on 12-28-2017, 03:15 PM
Default

To see the pics, use Chrome or Firefox and install the Photobucket extension onto whatever of the two browsers you use. I can see the pics on Chrome with the extension mentioned without issue.
Reply With Quote
  #5  
By BlackBMWs on 12-28-2017, 03:41 PM
Default DIY - How to install an E36 X-Brace on your TI

Cool, magic! thanks Dave! I’ll give that a try.

Did the DIY help?

I will update the DIY to not drill out the holes in the front subframe, rather, tap the nutserts in with a hammer, (I used a two lb Harbor Freight mini sledge hammer) then use the Allen bolts to crush them.

I install six Nutserts now to accommodate the two M undershield mount points.



Sent from my iPhone using Tapatalk
Last edited by BlackBMWs; 12-28-2017 at 03:50 PM..
Reply With Quote
  #6  
By 740isport on 12-28-2017, 03:52 PM
Default

DIY will help, was just reading it over as I haven't installed the bar yet, but will after I get rid of the white one! Thanks again.
Reply With Quote
  #7  
By sirius815 on 01-01-2018, 02:42 PM
Default

Got the part number for the nutserts?
Reply With Quote
  #8  
By BlackBMWs on 01-01-2018, 07:28 PM
Default

Quote:
Originally Posted by sirius815 View Post
Got the part number for the nutserts?

PN# 51718175003.

Updated the parts list in the DIY as well. Cheers!
Reply With Quote
  #9  
By BlackBMWs on 01-01-2018, 07:31 PM
Default

Quote:
Originally Posted by 740isport View Post
To see the pics, use Chrome or Firefox and install the Photobucket extension onto whatever of the two browsers you use. I can see the pics on Chrome with the extension mentioned without issue.
Thanks Dave! I can see the photos once again! I used the Chrome extension.

Reply With Quote
  #10  
By Pedro Cação on 09-03-2018, 08:56 PM
Default

Thank you for the tutorial BlackBMWs
Reply With Quote
Comment

Bookmarks


Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
 
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Tutorial Tutorial Starter Category Comments Last Post
S54 engine into late model E36 swap (same 318ti) Hakentt-MS41.1 Engine Swaps 11 11-03-2015 05:08 PM
spotted: ti atrocity vsonix Lounge 33 04-22-2012 04:58 PM
Sold the wrong oil pan HELP! fast2002 Maintenance 4 01-27-2012 05:16 AM
Need a new nose panel. Can any e36 fit? RCV7 Exterior 16 03-22-2011 11:59 PM
E46 323 rotors to fit the ti? BMW_Hatchback Brakes 15 04-09-2008 04:31 PM


All times are GMT +1. The time now is 08:32 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 78.12 k/102.15 k (23.52%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.