318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base

Notices

Knowledge Base How to articles and things explained.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Comments, 100,124 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Comments, 63,036 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Comments, 60,270 Views
Comment Share/Bookmark
 
Tutorial Tools Display Modes
Old 11-03-2011, 09:36 PM  
CirrusSR22
Senior Member
 
Join Date: Nov 2004
Location: Minneapolis
Posts: 1,587
iTrader: (3)
Default DIY: Timing Case Cover Gaskets and Chain Guides

DIY: Timing Case Cover Gaskets (Upper and Lower), Timing Chain Guides, Timing Chain Tensioner, Thermostat.

---------------------------------

I decided to finally tackle an intermittent oil leak. From what I could tell this leak was coming from the lower timing case...

Last edited by CirrusSR22; 11-10-2011 at 07:21 AM.
CirrusSR22 is offline   Reply With Quote
  #15  
By eurohb on 05-11-2012, 10:35 PM
Default

correct, since you need to hold the pulley in place in order to remove the front case.
Reply With Quote
  #16  
By paul somlo on 06-06-2014, 06:18 AM
Default

Umm... regarding those fasteners that hold the AC compressor on - is one of the three on the top of the compressor, accessible only from below, but not visible?
The picture was taken from below and the 6mm allen wrench is engaged with the fastener, the head of which points to the rear of the vehicle. To the left, one of the AC compressor bracket bolts is visible - it's the recessed one that can't be accessed with the compressor in place. Before I loosen that 3rd fastener, I just want to be sure that's the one, and not some fastener holding the compressor case together. And if that is the one, how did you deal with it? Also, I'm wondering if the inaccessible bracket bolt might be accessed with a 13mm offset box end wrench, rather than unbolting the compressor from the bracket?

Paul
'96ti 211,000mi



Attached Images
File Type: jpg P6050956.JPG (82.5 KB, 128 views)
Reply With Quote
  #17  
By Biolite on 06-06-2014, 02:32 PM
Default

For that one, I removed the AC compressor from the bracket and secured it out of the way (as much as feasibly possible) so it wasn't hanging on the hoses the whole time. Then that bolt becomes accessible. I think I used to a 1/4" drive socket wrench for it since the space was so tight.
Reply With Quote
  #18  
By paul somlo on 09-06-2014, 01:53 AM
Default

Replaced my timing cover gaskets several months ago and I've been meaning to post this. Here's how I dealt with the upper bolt that holds the compressor to the bracket - the allen wrench is 6mm, while the ratcheting box end wrench is 1/4", which is the closest thing I had.
Attached Images
File Type: jpg P9051008.JPG (84.7 KB, 45 views)
Reply With Quote
  #19  
By paul somlo on 08-20-2016, 04:12 PM
Default

The gasket that the arrow points to in the picture below - I suppose I would need to remove the cylinder head to replace it?
Attached Images
File Type: jpg e36 cyl head gasket.jpg (63.6 KB, 57 views)
Reply With Quote
  #20  
By cgillchico on 12-12-2016, 05:17 AM
Default

Quote:
Originally Posted by paul somlo View Post
The gasket that the arrow points to in the picture below - I suppose I would need to remove the cylinder head to replace it?
Yes and I would suggest using grey rtv to seal the nubs on the ends.
Reply With Quote
  #21  
By paul somlo on 12-13-2016, 10:15 PM
Default

Quote:
Originally Posted by cgillchico View Post
Yes and I would suggest using grey rtv to seal the nubs on the ends.
Wish you had told me that two months ago. I tried the procedure in the Bentley manual, using a piece of 0.006" spring steel in place of the BMW special tool. I never could pull the sheet metal out without the gasket distorting, so I ended up removing the head. Not a bad job in September, but not enjoyable in December in Colorado, in an unheated garage. Good thing I've got a spare ride.
Reply With Quote
  #22  
By karlis189 on 10-31-2017, 10:11 AM
Default

Can't see any pictures.. any help with that?
Reply With Quote
  #23  
By paul somlo on 10-31-2017, 06:54 PM
Default

Some of the pics are visible, some were apparently loaded to photobucket, however.
Reply With Quote
  #24  
By 96318ticali on 08-16-2020, 02:53 AM
Default

This photo shows the water pump installed with the lower timing cover removed. Based on this photo, is it accurate to infer that the lower timing chain cover CAN be removed without removing the water pump?

http://www.318ti.org/forum/attachmen...5&d=1471705897
Reply With Quote
  #25  
By paul somlo on 08-16-2020, 03:57 AM
Default

Quote:
Originally Posted by 96318ticali View Post
This photo shows the water pump installed with the lower timing cover removed. Based on this photo, is it accurate to infer that the lower timing chain cover CAN be removed without removing the water pump?

http://www.318ti.org/forum/attachmen...5&d=1471705897
I've been told so, although I wasn't able to. I think I may have had some casting flash on the pump that was hanging up the cover. There may be slight differences in how the castings come out of the mold, I suppose it's also possible that there was a slight change in the casting at some point. At any rate, I think it's a very close fit between the pump and cover.

I went through the paces early this summer of trying to fix my oil leaks (for the 2nd or 3rd time). Took the transmission off, replaced the rear seal, put the seal carrier back in with RTV and deleted the factory gasket. Removed both timing covers, deleted the factory gasket, sealed it very well with RTV. Still getting leaking where the trans and engine meet and still have a leak at the timing cover interface - I'm thinking where the two covers and profile gasket converge. A drop every few days, but still annoying. I give up, I'll just drive it, tired of chasing the oil leaks. I might try changing the oil pan gasket next oil change, but not optimistic. It's funny - that saying, "you know your BMW's low on fluids when it stops leaking", that rings true. Because of the way the oil pan is canted side to side, when I'm down a quart or so, no more leaking from the back of the engine.
Reply With Quote
  #26  
By 96318ticali on 08-16-2020, 03:23 PM
Default

LOL, Thanks for your reply. The car has over 230K miles and I'm uncertain how many miles are on the water pump. I think I'll swap in a new pump while I'm in there because if I don't it will probably start leaking the following week. Haha. This is my second ti and I enjoy the car very much. Happy motoring!
Reply With Quote
Comment

Bookmarks


Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
 
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Tutorial Tutorial Starter Category Comments Last Post
FL Brand New Timing Gaskets Viper3812 US and North America 1 09-27-2011 03:04 AM
Timing Chain Cover Gasket Ray Cism Lounge 26 05-12-2009 09:40 PM


All times are GMT +1. The time now is 11:47 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 79.00 k/106.19 k (25.61%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.