318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base

Notices

Knowledge Base How to articles and things explained.

.
» Recent Threads
1.9 drivetrain for sale...
Today 03:59 AM
Last post by qccabrio
Today 03:59 AM
0 Comments, 44 Views
New to forum...new to...
06-25-2017 12:11 PM
Last post by J!m
Today 01:54 AM
3 Comments, 236 Views
Fs: 96 ti s50 swap
10-17-2016 07:19 PM
Last post by BMW_Hatchback
Today 01:41 AM
10 Comments, 4,742 Views
Central locking remote...
Yesterday 10:19 PM
Last post by DGWGuitars
Yesterday 10:19 PM
0 Comments, 69 Views
Black Armrest for...
06-22-2017 08:22 PM
Last post by youngnikolai
Yesterday 07:59 PM
2 Comments, 230 Views
The 318ti OBD-II engine...
10-19-2006 06:48 PM
Last post by J!m
Yesterday 03:32 PM
57 Comments, 32,217 Views
97 318ti No Crank No...
06-27-2014 04:25 AM
Last post by manson_magot
Yesterday 11:38 AM
24 Comments, 11,542 Views
Another Swapped Ti
11-19-2016 06:43 PM
Last post by ZEK
Yesterday 03:54 AM
24 Comments, 6,670 Views
3.42 diff for auto?
06-26-2017 01:15 AM
Last post by J!m
Yesterday 02:18 AM
3 Comments, 251 Views
List of People Who Live...
07-02-2007 04:28 AM
Last post by cobaltbloo
06-26-2017 03:31 PM
70 Comments, 21,174 Views
Comment Share/Bookmark
 
Tutorial Tools Display Modes
Old 11-03-2011, 09:36 PM  
CirrusSR22
Senior Member
 
Join Date: Nov 2004
Location: Minneapolis
Posts: 1,585
iTrader: (3)
Default DIY: Timing Case Cover Gaskets and Chain Guides

DIY: Timing Case Cover Gaskets (Upper and Lower), Timing Chain Guides, Timing Chain Tensioner, Thermostat.

---------------------------------

I decided to finally tackle an intermittent oil leak. From what I could tell this leak was coming from the lower timing case...

Last edited by CirrusSR22; 11-10-2011 at 06:21 AM.
CirrusSR22 is offline   Reply With Quote
  #15  
By eurohb on 05-11-2012, 10:35 PM
Default

correct, since you need to hold the pulley in place in order to remove the front case.
Reply With Quote
  #16  
By paul somlo on 06-06-2014, 06:18 AM
Default

Umm... regarding those fasteners that hold the AC compressor on - is one of the three on the top of the compressor, accessible only from below, but not visible?
The picture was taken from below and the 6mm allen wrench is engaged with the fastener, the head of which points to the rear of the vehicle. To the left, one of the AC compressor bracket bolts is visible - it's the recessed one that can't be accessed with the compressor in place. Before I loosen that 3rd fastener, I just want to be sure that's the one, and not some fastener holding the compressor case together. And if that is the one, how did you deal with it? Also, I'm wondering if the inaccessible bracket bolt might be accessed with a 13mm offset box end wrench, rather than unbolting the compressor from the bracket?

Paul
'96ti 211,000mi



Attached Images
File Type: jpg P6050956.JPG (82.5 KB, 66 views)
Reply With Quote
  #17  
By Biolite on 06-06-2014, 02:32 PM
Default

For that one, I removed the AC compressor from the bracket and secured it out of the way (as much as feasibly possible) so it wasn't hanging on the hoses the whole time. Then that bolt becomes accessible. I think I used to a 1/4" drive socket wrench for it since the space was so tight.
Reply With Quote
  #18  
By paul somlo on 09-06-2014, 01:53 AM
Default

Replaced my timing cover gaskets several months ago and I've been meaning to post this. Here's how I dealt with the upper bolt that holds the compressor to the bracket - the allen wrench is 6mm, while the ratcheting box end wrench is 1/4", which is the closest thing I had.
Attached Images
File Type: jpg P9051008.JPG (84.7 KB, 26 views)
Reply With Quote
  #19  
By paul somlo on 08-20-2016, 04:12 PM
Default

The gasket that the arrow points to in the picture below - I suppose I would need to remove the cylinder head to replace it?
Attached Images
File Type: jpg e36 cyl head gasket.jpg (63.6 KB, 20 views)
Reply With Quote
  #20  
By cgillchico on 12-12-2016, 04:17 AM
Default

Quote:
Originally Posted by paul somlo View Post
The gasket that the arrow points to in the picture below - I suppose I would need to remove the cylinder head to replace it?
Yes and I would suggest using grey rtv to seal the nubs on the ends.
Reply With Quote
  #21  
By paul somlo on 12-13-2016, 09:15 PM
Default

Quote:
Originally Posted by cgillchico View Post
Yes and I would suggest using grey rtv to seal the nubs on the ends.
Wish you had told me that two months ago. I tried the procedure in the Bentley manual, using a piece of 0.006" spring steel in place of the BMW special tool. I never could pull the sheet metal out without the gasket distorting, so I ended up removing the head. Not a bad job in September, but not enjoyable in December in Colorado, in an unheated garage. Good thing I've got a spare ride.
Reply With Quote
Comment

Bookmarks


Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
 
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Tutorial Tutorial Starter Category Comments Last Post
FL Brand New Timing Gaskets Viper3812 US and North America 1 09-27-2011 03:04 AM
Timing Chain Cover Gasket Ray Cism Lounge 26 05-12-2009 09:40 PM


All times are GMT +1. The time now is 09:57 AM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2017, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 76.70 k/97.77 k (21.55%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.