318ti.org forum

Go Back   318ti.org forum > Technical, Maintenance and Modifications > Knowledge Base

Notices

Knowledge Base How to articles and things explained.

.
» Recent Threads
1999 M-Sport For Sale
12-31-2023 05:10 PM
Last post by Coop540iT
03-23-2024 06:39 PM
1 Comments, 105,915 Views
Once again 318ti owner...
03-20-2024 12:39 PM
Last post by two30grain
03-22-2024 02:04 PM
1 Comments, 68,878 Views
What brakes do I...
03-20-2024 03:27 PM
Last post by huirtera
03-20-2024 03:27 PM
0 Comments, 66,116 Views
Comment Share/Bookmark
 
Tutorial Tools Display Modes
Old 01-14-2008, 09:48 PM  
540318
Junior Member
 
Join Date: Jan 2008
Location: boston
Posts: 24
iTrader: (0)
Default DIY Starter replacement - with PICs

In a prior thread (see “Can I access my starter bolt from the radio slot?”) two ways to get to the starter bolts were discussed: 1) Remove the intake manifold, or 2) Drop the shaft/exhaust, loosen the transmission brace and tilt down the engine/transmission slightly to access starter from the...
540318 is offline   Reply With Quote
  #15  
By fieldhb on 09-08-2009, 02:41 AM
Default My Starter is starting to go.

Thanks for he write-up.
I am looking to replace the starter in my car, and would like to see the pictures also.
Any chance of getting those posted somewhere ?
Reply With Quote
  #16  
By dguzzardo22 on 09-08-2009, 07:46 AM
Default

im in the same boat aswell even tho its my 3rd starter i still would like pics also ..
Reply With Quote
  #17  
By BMW_Hatchback on 09-26-2009, 08:07 PM
Default

pics are dead now
Reply With Quote
  #18  
By Xenocide on 09-26-2009, 08:29 PM
Default

easier on m52 so don't even worry about it BMW-Hatchback.
Reply With Quote
  #19  
By 30yrMbr on 10-09-2009, 01:35 AM
Default

Well, after too many weekend days and weekday evenings, Ladeda3's starter is finally replaced and FUNCTIONAL! WoooHooo...

Had to redo, undo and do again too many times, almost memorized where every connector and fastener goes. Except for the 3 nuts that were left over...
Reply With Quote
  #20  
By Platanos on 08-05-2010, 01:54 AM
Default

i am having a hell of a time getting the top bolt out. went out a bought a swivel head rachet and still no luck....don't know what else to do.


edit;;;;

Tried using a 12 point wrench.....stripped the damn bolt.


edit again;

What now, drop the tranny?
Last edited by Platanos; 08-05-2010 at 02:19 AM..
Reply With Quote
  #21  
By cooljess76 on 08-05-2010, 03:13 AM
Default

Quote:
Originally Posted by Platanos View Post
i am having a hell of a time getting the top bolt out. went out a bought a swivel head rachet and still no luck....don't know what else to do.


edit;;;;

Tried using a 12 point wrench.....stripped the damn bolt.


edit again;

What now, drop the tranny?
No, just disconnect the shifter linkage, put a jack under the back of the tranny, remove the two nuts on the tranny crossmember and driveshaft center support bearing and slowly lower the jack. The engine is going to tilt back towards the firewall, but it'll give you about 2 extra inches of clearance above the tranny from under the car. Older model Ti's had a bolt and nut on the upper starter bolt. My '95 clubsport had a bolt and nut, but my '97 and newer models have a threaded starter housing, so there's no nut to hold from the other side. Makes things a little easier, I forget which year they started using threaded starters.

BTW, the starter will drop out from under the car. All you have to do is remove the dipstick tube, rotate the starter 270 degrees lengthwise and drop it straight down. Make sure your battery is disconnected before disconnecting the wires going to the starter. No need to remove the intake manifold like someone mentioned, it's too much of a PITA and completely unecessary. Best of luck man, LMK if I can help.
Reply With Quote
  #22  
By Platanos on 08-06-2010, 11:21 PM
Default

Thanks cooljess, your tips helped out. I got everything buttoned up. Was a pain in the ass getting the intake back on. Why would they put that harness through the middle of the intake!?!?

Anyway, now my car won't start. I checked all my plugs and hoses. Everything is in it place. I swapped the two plugs going into the block (cps and something else?) because I wasn't sure which one was which. Still no start. Its cranking but won't turn over, it even sounds like its gonna start but then nothing. It backfires if I keep trying. This is extrememly frustrating..
Reply With Quote
  #23  
By Platanos on 08-06-2010, 11:46 PM
Default

Now I got her to start but she is intermittant. Not sure what else to do.
Reply With Quote
  #24  
By Colink on 09-06-2010, 02:53 PM
Default

I have a '96 model ti. How do I know if I need a starter with threaded mounting ears or un-threaded, without having to go in there and take it out?
Reply With Quote
  #25  
By Xenocide on 09-06-2010, 03:37 PM
Default

Get threaded ears, they are interchangeable. threaded ears are easier to install. If you buy it from autozone (which I recommend). They are both sold under the same part number so keep opening what ever boxes they have instock until you find one. I think It took me 2 or 3 boxes to find a starter with threaded ears.
Reply With Quote
  #26  
By 95white318ti on 10-26-2010, 03:14 PM
Default

Hi guys. I just read this and comments in search of which wire goes on the small top terminal and the bottom one. I read another and thought it said Ylw blk on the bottom one. Is this correct?
Reply With Quote
  #27  
By 3ggshell on 10-21-2011, 03:01 AM
Default

Hello, I'm in the process of removing my old starter and I got both bolts out from the bottom without removing anything - just using some wobbly extensions. I also have all the wiring disconnected, and the starter just will not come out. I was wondering if anybody has had this problem? I can see that I got the right bolts out, and I'm worried the PO has mushroomed the pin. I can get separation of about 1/8" and it will wiggle a little, but that it. Hopefully someone else has had similar problems.

Thanks
Reply With Quote
  #28  
By PixelRandy on 05-31-2014, 08:56 PM
Wink

This thread has been stagnant for a long time. I thought I'd chime in as I just (as in ten minutes ago) did swapped the starter in my '96 M44 ti. I already had the intake and cooling hoses out as I'm in the middle of rebuilding the cooling system. Seeing that the starter was right there, I didn't want to risk not replacing it. My car is just shy of 200k and I don't see any service records showing that any of the POs had replaced it. My car came with binder of records too.

Tools you really need to do this right, and I can't emphasize this enough:

- SWIVEL HEAD SOCKET WRENCH
- E12 SOCKET

Trying to use anything else to get the two bolts out is half-assing the job. The firewall is directly above the two bolts, so you need a handle that came come back towards you (even just 10*) to clear the firewall.

I found that on my car, once the bolts were broken free a turn or two, they came out with finger pressure. Whew!

The starter did stick on the locating pin. A little VERY gentle prying while rocking and it came right out.

I noticed that the new starter didn't want to slide back over the locating pin easily, and you don't want to bang on the starter as you can damage the magnets. I took a bit of fine sand paper and took off the surface gunk on the locating pin. This allowed the new starter to fully seat with hand pressure with a little rocking.

I also cleaned off a bit of the corrosion that was on the two bolts and put a dab of anti-seize on the threads. I was able to finger tighten each bolt all they way until they bottomed out. Just a half or three-quarters turn on each with the wrench until tight.

I hate working way back there. It's just asking for muscle cramps. Man, I'm really out of shape!

Good luck!
Reply With Quote
  #29  
By alika808 on 11-15-2014, 07:13 AM
Default

Great Job. Perfect I need this DIY and makes my project easier. Thank you.
Reply With Quote
Comment

Bookmarks


Currently Active Users Viewing This Tutorial: 1 (0 members and 1 guests)
 
Tutorial Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump

Similar Threads
Tutorial Tutorial Starter Category Comments Last Post
FS: 1995 Alpine White 318ti Sport Package 95ti_santabarbara US and North America 19 10-28-2008 02:28 PM
'97 318ti 5-spd, white, Active, 103k miles in Virginia Phil Marx US and North America 12 04-24-2008 03:40 AM
White or Black out? BmWwHiPPin Exterior 8 01-25-2006 08:09 PM
White ti sighting Juni New England - US 5 11-22-2005 04:43 PM
White Ti on Trapelo Rd (Waltham,Ma) Tyler Misc 4 10-03-2005 07:09 PM


All times are GMT +1. The time now is 12:06 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006
© vBadvanced CMPS v3.2.2
[page compression: 84.74 k/115.11 k (26.38%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.