Forum: Transmission 02-08-2013, 03:20 AM |
Replies: 14 Views: 3,860 Yep! No doubt. Good luck! |
Forum: Transmission 02-07-2013, 05:30 AM |
Replies: 14 Views: 3,860 Almost one year later... I got an error message trying to answer a private message, so here's the question and response pasted below . . . I did have trouble with pilot bearing...the one supplied was damaged and... |
Forum: Transmission 03-25-2012, 08:42 PM |
Replies: 14 Views: 3,860 Will it fit??? According to realoem.com the ti... Will it fit??? According to realoem.com the ti has--S5D 250G - TBDH Will a Getrag 250G - TAJT (FROM A 1999 323) fit into a ti with no modifications? What is the difference between the initials... |
Forum: Transmission 03-25-2012, 07:10 PM |
Replies: 14 Views: 3,860 |
Forum: Transmission 03-25-2012, 06:25 PM |
Replies: 14 Views: 3,860 |
Forum: Transmission 03-25-2012, 05:07 PM |
Replies: 14 Views: 3,860 Clutch/Flywheel Replacement...Gear box too? Well I haven't posted in a while, but that's because my ti has been running great--until the clutch went out. I have it torn down, here's the situation: With questions. . .1996 ti with 243,000... |
Forum: Transmission 09-27-2011, 04:55 PM |
Replies: 21 Views: 8,576 Not messing with output flange. Bummer on the bad bolts. Don't remember if I put new ones on when I did the cylinder head or not, but pretty sure they were never studs or pressed on my head pipe. Yep, preparing list for shift... |
Forum: Transmission 09-27-2011, 03:36 PM |
Replies: 21 Views: 8,576 Yep. Flange bolts broke. Yes, I did remove the "mid-pipe" (cat conv) to gain access to center bearing bolts. If you unscrew a few other retaining nuts, there's plenty of slack in the O2 sensor wires to put cat pipe on floor... |
Forum: Transmission 09-27-2011, 02:16 PM |
Replies: 21 Views: 8,576 Where did you get it? I'm looking around and I'm seeing 350-550 on prices for reman driveshafts. My driveshaft is currently on the garage floor. What to do, what to do... |
Forum: Transmission 08-28-2011, 05:04 AM |
Replies: 21 Views: 8,576 |
Forum: Transmission 08-28-2011, 04:41 AM |
Replies: 21 Views: 8,576 Does this sound like drive shaft problem? 96... Does this sound like drive shaft problem? 96 with 237k on chassis. (new diff mount, trans mount, and engine mounts are already installed) When slowing down-coasting-especially in 4th gear, there... |
Forum: Interior and ICE 07-27-2011, 02:43 PM |
Replies: 6 Views: 1,400 Thanks for quick answer, thought so. . . Ya, I do use that site for finding parts, just not that familiar with the cross ref section. From a quick glance though it does look like a few little things like window switches and bezel plates... |
Forum: Interior and ICE 07-27-2011, 01:32 PM |
Replies: 6 Views: 1,400 Seat Swap 91 wagon to 96 ti? Hi guys. My cousin has a junkyard bound 91 325 i station wagon. It has electric leather seats. My 96 ti has mechanical seats. Can I swap the seats leaving the mechanical operations in my ti? ... |
Forum: Suspension 05-26-2011, 10:42 PM |
Replies: 32 Views: 9,113 Was bent all along. . . Yep, the trailing arm was bent all along, but I didn't see it until after I had replace subframe and rta bushings. It's only been about 2,000 miles, so if I don't see anything obvious, then I'll... |
Forum: Suspension 05-26-2011, 05:20 PM |
Replies: 32 Views: 9,113 IE RTABs reusable? I was just wondering... I'm gonna have to replace a bent trailing arm. Unfortunately, I already put new IE bushings in just a couple thousand miles ago. My question is can I reuse these in the new... |
Forum: Lounge 12-03-2010, 10:04 PM |
Replies: 22 Views: 7,288 Okay, here's one new observation--the stock... Okay, here's one new observation--the stock exhaust actually comes in contact with the axle housing--sometimes I hear a rattle, sometimes not, which means axle housing takes a different position over... |
Forum: Lounge 12-03-2010, 02:34 PM |
Replies: 22 Views: 7,288 So the question is... ...will replacing subframe bushings bring rear camber back into specs? (provided that the left rear trailing arm is not bent?) Cuz that's what it's starting to look like. Off to the junkyard then,... |
Forum: Lounge 12-03-2010, 05:29 AM |
Replies: 22 Views: 7,288 Teacher who likes (needs) to learn. Okay, I'm glad I have your attention for a minute. As I was waiting to put the engine back together, I replaced the following front suspension: All OEM-or equal, struts lower control arms ... |
Forum: Lounge 12-02-2010, 11:08 PM |
Replies: 22 Views: 7,288 Same here. . . Bought a ti had a blown engine, so didn't get to drive it much. All fixed now. The big issue now is what you guys are talking about. I have learned that when you're surfing at tirerack and some... |
Forum: US and North America 12-01-2010, 11:43 PM |
Replies: 6 Views: 2,555 |
Forum: US and North America 11-29-2010, 06:02 AM |
Replies: 6 Views: 2,555 |
Forum: US and North America 11-24-2010, 03:56 PM |
Replies: 4 Views: 1,104 Waiting for Pics Hello: I'm interested and would like to see some pictures when you get a chance. I have 4 bent LTW replicas on my TI and I think I'm gonna have trouble getting around in the snow here in... |
Forum: Electrical 11-23-2010, 11:24 PM |
Replies: 14 Views: 6,108 |
Forum: Electrical 11-23-2010, 12:22 AM |
Replies: 14 Views: 6,108 |
Forum: Electrical 11-22-2010, 09:45 PM |
Replies: 14 Views: 6,108 The symptoms. Okay, it's all screwed up now. Had water coming in antenna hole back there. And now the list. No brake lights at all. (brake light switch?) No instrument cluster illumination. (bad rheostat on... |