318ti.org forum

Go Back   318ti.org forum > Search Forums

Notices

.
Showing results 1 to 9 of 9
Search took 0.00 seconds.
Search: Posts Made By: LennyG
Forum: Lounge 01-26-2011, 06:08 PM
Replies: 9
Views: 9,024
Posted By LennyG
Thumbs up The Deed is DONE

:biggrin:I finished the installation of an M44 with 45K on it. It came complete so I cut the loom and wired all of the new engine components into the car. Only three of the 29 wires had to be traced...
Forum: I'm thinking about buying a ti. 10-25-2010, 02:09 PM
Replies: 8
Views: 2,575
Posted By LennyG
Thumbs up The car is available...

I am installing another engine right now. I will be finished with it this weekend. The car only has 104K, but the radiator blew all of the coolant on a really hot day and my daughter didn't see the...
Forum: I'm thinking about buying a ti. 09-13-2010, 02:32 PM
Replies: 8
Views: 2,575
Posted By LennyG
If you're still looking for an Auto ti, have some...

If you're still looking for an Auto ti, have some patience and I will have mine built in a few weeks. I am putting in the new engine now. I have to replace the driver's regulator and install the new...
Forum: Engine Swaps 09-11-2010, 08:37 PM
Replies: 0
Views: 768
Posted By LennyG
Post Wanted!! 98 M44 Engine

I am ready to pull the engine, but I still need its replacement. I thought I would have found the right one by now. Can anyone help? If you have one, send price, miles and compression....
Forum: Lounge 09-09-2010, 01:50 PM
Replies: 9
Views: 9,024
Posted By LennyG
Thanks for the follow-up. The deed is done and it...

Thanks for the follow-up. The deed is done and it was a piece of cake. I took a set of pictures of the procedure and will post them to the thread as soon as I can. Your advice and the pics I took are...
Forum: Lounge 09-07-2010, 03:35 PM
Replies: 9
Views: 9,024
Posted By LennyG
You just made my day. I thought I was going to...

You just made my day. I thought I was going to have to pay another $100 for another "special tool". Punch, Breaker bar and Pipe I have.
Thank you much.
Forum: Lounge 09-05-2010, 04:37 PM
Replies: 9
Views: 9,024
Posted By LennyG
Question Crankshaft center bolt removal

I have to get the crank bolt off of my engine. The spec is 240lb/ft and I have a feeling it is even tighter than that. I have locked it up to the frame with the breakerbar to use the starter and all...
Forum: Lounge 08-20-2010, 07:32 PM
Replies: 3
Views: 974
Posted By LennyG
Right now all I have is a Great car containing a...

Right now all I have is a Great car containing a fried 1.9L engine. I have to decide whether to continue with a long block or sell it. I got it for my daughter, but she has been stuck driving the...
Forum: Lounge 08-15-2010, 07:00 PM
Replies: 3
Views: 974
Posted By LennyG
Thumbs up I will need some education; I just signed up.

The similar thread the system found was fun; however, all I wanted to do was say "Hi" to everyone. I've read some of the discussions and always came away with new knowledge. I am really looking...
Showing results 1 to 9 of 9

 
Forum Jump

All times are GMT +1. The time now is 05:13 PM.


.
Powered by site supporters
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
[page compression: 42.39 k/48.72 k (12.99%)]

318ti.org does not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any information or products discussed.