Forum: Parting out & Parts (US) 07-31-2018, 04:17 PM |
Replies: 6 Views: 3,328 |
Forum: Engine 05-18-2018, 09:32 PM |
Replies: 2 Views: 3,092 Yep. #6 is where the leak is coming from most... Yep. #6 is where the leak is coming from most likely. I had to chase mine down recently. It leaks behind the cowl and runs down the water drains making it look like the back of the engine. Replace #6... |
Forum: Parting out & Parts (US) 12-06-2017, 10:32 PM |
Replies: 4 Views: 2,709 |
Forum: Engine 11-01-2017, 08:07 PM |
Replies: 1 Views: 892 |
Forum: Engine 09-02-2017, 10:25 PM |
Replies: 1 Views: 2,176 |
Forum: Engine 09-02-2017, 01:37 PM |
Replies: 1 Views: 2,176 Engine block cooling passages I'm cleaning up the block in preparation for a new cylinder head. I'm cleaning up all the rust from the coolant passages but I have a question about the 2 little holes (not the 2 big holes) in... |
Forum: Parting out & Parts (US) 08-10-2017, 04:32 PM |
Replies: 2 Views: 1,682 |
Forum: Parting out & Parts (US) 08-10-2017, 04:22 PM |
Replies: 2 Views: 1,682 WTB: M42 cylinder head I pulled my cylinder head and found that it is cracked in 2 places. I'm in need of a m42 cylinder head. Since shipping would be expensive, I would like to see if anyone has one in the south east near... |
Forum: Parting out & Parts (US) 05-11-2017, 12:52 AM |
Replies: 3 Views: 2,162 |
Forum: Engine 04-23-2017, 03:52 AM |
Replies: 5 Views: 1,979 |
Forum: Engine 04-21-2017, 09:06 PM |
Replies: 5 Views: 1,979 I recently just repaired the mess under the... I recently just repaired the mess under the intake when I did my knock sensors. Everything that I found leaking with a smoke machine before teardown was repaired/replaced. (PCV valve, DISA vacuum... |
Forum: Engine 04-21-2017, 06:01 PM |
Replies: 5 Views: 1,979 Does this DME look water damaged? I'm trying to figure out why my m42 runs pig rich and won't idle for the 1st 10-20 seconds on a cold start. Doesn't matter if hot or cold outside. As the title states, what do y'all think? I also... |
Forum: Parting out & Parts (US) 04-20-2017, 02:13 AM |
Replies: 21 Views: 6,982 |
Forum: Engine 04-10-2017, 03:28 PM |
Replies: 13 Views: 3,344 |
Forum: Engine 04-10-2017, 03:04 PM |
Replies: 13 Views: 3,344 |
Forum: Engine 04-10-2017, 02:26 PM |
Replies: 13 Views: 3,344 |
Forum: Engine 04-10-2017, 03:09 AM |
Replies: 13 Views: 3,344 |
Forum: Engine 04-01-2017, 01:31 AM |
Replies: 13 Views: 3,344 Welp. Looks like I still got more problems then... Welp. Looks like I still got more problems then just an AFM. Still starts up then stalls. Have to apply some throttle for it to finally start and run. Let go of the throttle and stalls. It also seems... |
Forum: Engine 03-31-2017, 10:15 PM |
Replies: 13 Views: 3,344 |
Forum: Parting out & Parts (US) 03-30-2017, 12:51 AM |
Replies: 38 Views: 13,731 |
Forum: Engine 03-29-2017, 02:23 AM |
Replies: 13 Views: 3,344 Well, I think there is more to it. Now that I... Well, I think there is more to it. Now that I have the icv plugged in and the engine is idling 800-1000 rpm, I can disconnect it and the revs go up. Sprung open allowing more air to enter. I bench... |
Forum: Engine 03-28-2017, 04:09 AM |
Replies: 13 Views: 3,344 AFM or not to AFM. That is the question. Hey all. If you saw my knock sensor and under the intake project, then you will know kinda what's going on. I've got a cold start idle issue as well as an all around idle problem at all temps for... |
Forum: Engine 03-27-2017, 05:15 AM |
Replies: 5 Views: 13,691 All new o-rings for the injectors. Cleaned up... All new o-rings for the injectors. Cleaned up nicely and look like new. https://uploads.tapatalk-cdn.com/20170327/1f462c8d1337c76fc504f79068045a24.jpg "Squid" installed. Worst part of the job... |
Forum: Engine 03-25-2017, 06:16 AM |
Replies: 5 Views: 13,691 |
Forum: Parting out & Parts (US) 03-16-2017, 02:06 PM |
Replies: 8 Views: 7,862 |