Forum: Parting out & Parts (US) 03-15-2018, 09:57 PM |
Replies: 52 Views: 25,209 |
Forum: Interior and ICE 03-05-2018, 11:42 PM |
Replies: 4 Views: 1,711 |
Forum: Interior and ICE 03-05-2018, 11:40 PM |
Replies: 4 Views: 1,711 IMO, just changing the head unit to a decent... IMO, just changing the head unit to a decent aftermarket will do wonders. I wouldn't bother running a sub off the factory deck. I have a good Pioneer deck running highs through the factory amp (I... |
Forum: Music to drive by 03-05-2018, 08:47 PM |
Replies: 11 Views: 10,113 |
Forum: Exterior 02-01-2018, 10:57 PM |
Replies: 26 Views: 16,353 |
Forum: Lounge 11-15-2017, 11:59 PM |
Replies: 316 Views: 199,631 |
Forum: Engine 10-09-2017, 04:58 PM |
Replies: 6 Views: 1,682 I found this out the hard way :redface: That... I found this out the hard way :redface: That sounds more like an alternator to me. My tensioner made more of a humming noise when it went. If you have a long screwdriver or piece of rod, hold one... |
Forum: Misc 07-24-2017, 10:38 PM |
Replies: 2 Views: 1,434 |
Forum: Engine 07-24-2017, 08:30 PM |
Replies: 4 Views: 3,265 |
Forum: Engine 07-24-2017, 08:24 PM |
Replies: 4 Views: 3,265 |
Forum: Engine 07-24-2017, 08:22 PM |
Replies: 6 Views: 2,435 |
Forum: Engine 07-20-2017, 11:53 PM |
Replies: 4 Views: 3,265 Changed my cam timing today-impressions So I've been thinking about playing with my cam timing for a few months now. There was a thread a while back on this trying to figure out what the optimal settings are, but there didn't seem to be... |
Forum: Engine 07-20-2017, 11:26 PM |
Replies: 6 Views: 2,435 No cam phasing on this M44. Definitely runs... No cam phasing on this M44. Definitely runs better with a good sensor, though. Fuel economy seems to have improved slightly. I played with my cam timing today, but I'll post that in another thread. ... |
Forum: Parting out & Parts (US) 06-23-2017, 07:43 PM |
Replies: 19 Views: 13,555 |
Forum: Engine 06-14-2017, 04:28 PM |
Replies: 6 Views: 2,435 |
Forum: Engine 06-12-2017, 03:34 PM |
Replies: 6 Views: 2,435 Cam sensor question My M44 is throwing a cam sensor code,but the car seems to run fine. Will this affect anything else, i.e. power, fuel economy, etc? Trying to decide how critical this problem is. Thanks, Scott |
Forum: Knowledge Base 05-09-2017, 02:21 PM |
Replies: 17 Views: 53,162 Yes, low charge will cause short cycling. What... Yes, low charge will cause short cycling. What that means is the compressor is cycling out too soon and doesn't run long enough to work properly. There is a pressure switch on the low pressure side... |
Forum: US and North America 05-08-2017, 07:12 PM |
Replies: 12 Views: 4,327 |
Forum: US and North America 05-08-2017, 05:49 PM |
Replies: 12 Views: 4,327 |
Forum: Knowledge Base 05-08-2017, 03:03 PM |
Replies: 17 Views: 53,162 |
Forum: Engine 05-02-2017, 05:29 PM |
Replies: 75 Views: 40,834 Makes sense. I was wondering, though, if anyone... Makes sense. I was wondering, though, if anyone has tried this and found where that "sweet spot" might be. I'll be doing a valve cover gasket soon and might tweak a little to see what happens. I'm... |
Forum: Knowledge Base 05-02-2017, 05:20 PM |
Replies: 9 Views: 16,919 |
Forum: Engine 04-13-2017, 07:30 PM |
Replies: 11 Views: 6,786 Is the battery fully charged? If you have a... Is the battery fully charged? If you have a voltmeter, check the voltage across the battery terminals while someone spins it over, or rig it up so you can watch the meter. You should stay close to 12... |
Forum: Lounge 04-13-2017, 07:21 PM |
Replies: 2 Views: 1,466 Technically, evacuation is pulling a vacuum on... Technically, evacuation is pulling a vacuum on the system in preparation for charging. If you're talking about removing the existing refrigerant, that's recovering. Not sure why Jiffy Lube couldn't... |
Forum: Engine 03-28-2017, 11:10 PM |
Replies: 75 Views: 40,834 |