Forum: Parting out & Parts (US) 05-04-2020, 08:00 PM |
Replies: 8 Views: 14,256 |
Forum: Parting out & Parts (US) 05-04-2020, 07:55 PM |
Replies: 8 Views: 14,256 |
Forum: Suspension 01-24-2020, 02:09 PM |
Replies: 0 Views: 4,917 Z3 6cyl rear suspension swap I was thinking of swapping my rear suspension setup after i finish rebuilding my E30 LSD. is anyone running 6 cyl Z3 trailing arms and rear sub frame? how does it compare to the standard ti rear end... |
Forum: Exterior 12-18-2019, 02:57 PM |
Replies: 3 Views: 9,760 yes, the ti does have a sedan front end, pretty... yes, the ti does have a sedan front end, pretty much any part of the car from the a pillar rear is ti specific. therefore sedan doors or coupe doors will not fit. the sedan doors are to short and are... |
Forum: Suspension 12-05-2019, 02:50 AM |
Replies: 3 Views: 5,055 |
Forum: Suspension 12-05-2019, 02:48 AM |
Replies: 3 Views: 5,055 bc racing or KWs? im looking at getting coilovers for my 97 318ti. i cant decide between bc racing (BR) coilovers or KW V1 coilovers. my friend is running BCs on his 88 MR2 and they feel good on his car and are at a... |
Forum: Wheels and Tires 11-11-2019, 01:56 PM |
Replies: 0 Views: 2,234 16x9 et 15 will these fit on the ti with only a fender roll? if so is anyone running similar specs and how is the fitment? |
Forum: Wheels and Tires 11-11-2019, 05:04 AM |
Replies: 0 Views: 2,647 Hartge reps anyone know where i can buy a rep of the 3 piece Hartge wheels its my dream wheel in my ti but, the real ones are too expensive so, i think a good quality rep will suit my purpose and look good... |
Forum: Exterior 09-30-2019, 06:33 PM |
Replies: 0 Views: 3,495 ebay M3 front bumper has anyone used one of the Chinese clone M3 front bumpers on ebay? anything i should look out for when buying one? how do they hold up to being daily driven? how has your experience been with it? |
Forum: Parting out & Parts (US) 09-27-2019, 06:58 PM |
Replies: 9 Views: 7,577 |
Forum: Parting out & Parts (US) 09-27-2019, 06:48 PM |
Replies: 0 Views: 3,405 wtb M-tech rear bumper cover 51122491226 trying to find an M-Tech rear bumper cover. i do not care what color but, must be in reasonably good condition and reasonably complete.. i would like to have one in the Nashville area but, anywhere... |
Forum: Electrical 09-23-2019, 01:30 AM |
Replies: 5 Views: 5,925 this should help ... this should help https://www.pelicanparts.com/BMW/techarticles/BMW-Z3/20-ELEC-Ignition_Switch_Replacement/20-ELEC-Ignition_Switch_Replacement.htm |
Forum: Electrical 09-23-2019, 12:25 AM |
Replies: 5 Views: 5,925 i have also needed a new switch in my car. you... i have also needed a new switch in my car. you can do to the dealership and you can get one that matches your key. overall its not very difficult but, for me it was a little easier because i used the... |
Forum: Engine Swaps 09-07-2019, 11:34 PM |
Replies: 1 Views: 12,326 the noise turned out to just be the amount of... the noise turned out to just be the amount of play in my rob bearings because i had gotten original sized ones when i actually needed oversize ones. but i still not 100% solid on my ring situation |
Forum: Engine Swaps 09-05-2019, 03:03 AM |
Replies: 1 Views: 12,326 m52b30 rings? i just put together the rotating assembly for my M52B30. its an M52 block with M54B30 crankshaft and full M54B30 piston assembly with new crank bearings, rod bearings and a set of M52 piston rings.... |
Forum: Engine Swaps 06-03-2019, 11:34 PM |
Replies: 2 Views: 2,688 god save me i am currently putting together the final parts to my 328ti swap. i am dressing the m52B28 (07/97) but, idiot me wasn't thinking about labeling my wiring harness. i have found several wiring diagrams... |
Forum: Engine Swaps 05-15-2019, 04:11 AM |
Replies: 0 Views: 1,527 M52B28 with junkyard M54B30 rotating assembly i today i bought a M54B30 short block. im gathering parts for "stage 2" of my build. anything i should know or check beforehand? im going to use my M52 iron block and use M54 crank and full piston... |
Forum: Parting out & Parts (US) 05-14-2019, 11:26 PM |
Replies: 15 Views: 18,271 |
Forum: Parting out & Parts (US) 05-09-2019, 12:02 AM |
Replies: 15 Views: 18,271 |
Forum: Engine Swaps 04-26-2019, 03:56 AM |
Replies: 2 Views: 2,278 trans second position? just a quick question for anyone who has done the M52 swap. i am currently gathering all the parts for my swap and ill be using my stock getrag trans. but, i have heard that you need to move the... |
Forum: Engine Swaps 12-29-2018, 08:00 AM |
Replies: 9 Views: 3,248 |
Forum: Engine Swaps 12-29-2018, 07:54 AM |
Replies: 9 Views: 3,248 |
Forum: Engine Swaps 12-28-2018, 12:27 PM |
Replies: 9 Views: 3,248 |
Forum: Suspension 12-26-2018, 07:09 AM |
Replies: 1 Views: 844 |
Forum: Engine Swaps 11-02-2018, 03:17 PM |
Replies: 1 Views: 1,375 Driveshaft compression? Greetings! I’m currently trying to gather all the parts necessary to M52 swap my ti but, I’ve heard from some that my driveshaft should compress enough to allow the M52 to be used with my stock... |