318ti.org forum (http://www.318ti.org/forum/index.php)
-   Knowledge Base (http://www.318ti.org/forum/forumdisplay.php?f=42)
-   -   Engine Mount Replacement DIY. PICS! (http://www.318ti.org/forum/showthread.php?t=23846)

CirrusSR22 09-30-2008 05:31 AM

Engine Mount Replacement DIY. PICS!
 
Engine Mount Replacement DIY


PARTS:
------------
Two engine Mounts. Part#11811141377 $44.95 each at AutohausAZ.com. Free Shipping. $89.90 total.


TOOLS:
--------------
• Ratchet
• ≥20” worth of extensions
• Universal joint
• 16mm socket (mine was a deep, but a standard should work)
• 13mm (?) socket for the transmission crossmember and x-brace bolts.
• Flathead screwdriver
• Hydraulic Floor jack
• Jack stands or Ramps
• Wheel chocks

PROCEDURE:
----------------------

• Safely raise and support front of vehicle with rear wheels chocked, parking brake firmly set, and car in park or in gear.

• Remove the factory x-brace if installed. Four bolts.
http://i44.photobucket.com/albums/f23/vasa58/mm7.jpg

• Loosen the four transmission crossmember bolts. Loosen as much as possible, but don’t remove as the weight of the transmission needs to rest on the bolts. This will allow the engine/transmission assembly to move with less strain on the transmission mounts.
http://i44.photobucket.com/albums/f23/vasa58/mm16.jpg

CirrusSR22 09-30-2008 05:32 AM

• Loosen top engine mount nuts with extensions. This was much easier than I thought it would be, but I needed to use a longer ratchet than the one pictured to break loose the nuts. Remove the driver’s side nut and washer, but leave the passenger side nut loosely on the threads

Socket Set-up
http://i44.photobucket.com/albums/f23/vasa58/mm1.jpg

Driver’s Side Pic #1
http://i44.photobucket.com/albums/f23/vasa58/mm2.jpg

Driver’s Side Pic #2
http://i44.photobucket.com/albums/f23/vasa58/mm3.jpg

Passenger’s Side Pic #1
http://i44.photobucket.com/albums/f23/vasa58/mm4.jpg

Passenger’s Side Pic #2
http://i44.photobucket.com/albums/f23/vasa58/mm5.jpg

Passenger’s Side Pic #3
http://i44.photobucket.com/albums/f23/vasa58/mm6.jpg

CirrusSR22 09-30-2008 05:32 AM

• From under the car, loosen the bottom engine mount nuts. Leave the passenger side nut in place, but loose. Removed the driver’s side nut completely.

Driver’s Side
http://i44.photobucket.com/albums/f23/vasa58/mm8.jpg

Passenger’s Side
http://i44.photobucket.com/albums/f23/vasa58/mm9.jpg

Access the nuts though the holes in the control arms.
http://i44.photobucket.com/albums/f23/vasa58/mm10.jpg

• Remove hose clamp from engine intake boot. This prevents tearing of the boot when engine is lifted.

• Gently and slowly jack the engine up using a piece of wood on the jack to distribute wieght evenly on the oil pan. Make sure no wires or hoses are binding as you lift the engine. By keeping the nuts on the passeneger side mount, the engine assembly with rotate as you lift it. I found this way easier than trying to lift the engine evenly on both sides.

Jacking engine up.
http://i44.photobucket.com/albums/f23/vasa58/mm11.jpg

• Remove and replace the driver’s side engine mount. Gently lower the engine back down onto the new engine mount, making sure the mount is properly lined up so you don’t damage the threads. I needed a long pipe to slightly lever the engine into position. There is a locating pin/hole to line up. See picture. Start the nuts on the threads, but don’t tighten them.

Top of the driver’s side mount not quite lined up.
http://i44.photobucket.com/albums/f23/vasa58/mm12.jpg

• Remove the nuts on the passenger’s side mounts. Gently and slowly jack the engine up using a piece of wood on the jack to distribute wieght evenly on the oil pan. Make sure no wires or hoses are binding as you lift the engine.

CirrusSR22 09-30-2008 05:33 AM

• Remove and replace the passeneger’s side engine mount. Gently lower the engine back down onto the new engine mount, making sure the mount is properly lined up. There is a locating pin & hole to line up. Start threading the nuts back onto place, but don’t tighten them. Make sure the heat shield (passenger side only) is back into pace.

Locating pin (passenger side).
http://i44.photobucket.com/albums/f23/vasa58/mm13.jpg

Passenger side in place.
http://i44.photobucket.com/albums/f23/vasa58/mm14.jpg

• Now that the engine is resting on the new mounts, double check to make sure the engine is properly lined up on the mounts. Tighten and torque the mount nuts. 33 ft-lbs. Use new nuts or Loctite or both.

http://i44.photobucket.com/albums/f23/vasa58/mm15.jpg

• Bolt everything else back into place. Don't forget the intake boot if you removed it.

mgbman69 08-01-2009 06:14 AM

Great write up! Very helpful.

gabe3 09-11-2009 09:58 PM

I just changed both engine mounts / motor mounts on my M44 on two different occasions, but within a week of each other.

I set out to replace the passenger side mount, which I could easily see was completely sheared. In the process of changing it, I saw that the driver side mount was also sheared.

This article was extremely helpful, and here are my two cents:

-Remove the wheels! You can see so much more and have unfettered access to where you need to be.

-This writeup is absolutely brilliant to recommend leaving the passenger side mount top nut on the bolt, but loose. This ensures that the more difficult drivers side mount is well aligned for replacement.

-Pay attention to how you removed the mounts, as this will be the easiest way to replace the new ones.

Thanks for this great writeup!

dave45056 08-30-2010 01:39 AM

Great write up... I just did this today along with my transmission mounts. This helped a lot. Thanks!

47driver 09-21-2010 03:37 AM

Thanks for the write up. I 'll have to give this a try.

bmorekirby 07-02-2011 05:27 PM

i just found this, and thank god because im doing my mounts today. thanks for the diy. yet another reason i love this forum!

Kaliimc 03-20-2012 08:53 PM

Guys, any noticeable change after changing both mounts?

I just saw mine when changing control arms last weekend and think I should change mine out based on the way they look.

spidertri 06-25-2012 10:56 PM

Finally did this today, once again, thanks for the awesome write up Cirrus. The whole job was way easier than I expected. Driver side was definitely more of a pain than the passenger side but not hard at all.

Telefunken 09-15-2014 02:25 AM

What would be a reasonable price for a mechanic to replace the engine mounts?

dynagroove 09-19-2016 02:06 AM

I know this is an old thread, but I just wanted to say that it's still useful and thank you for posting! I knew I had an issue with at least 1 mount, but turns out both mounts were broken. The tip on loosening the transmission mount was especially helpful. I went ahead and did the transmission mounts while I was down there. The car feels so much better now. Thanks again!

Outrider 09-16-2017 12:48 PM

Sadly, the photo links have gone dead. It would be great if all of the DIYs had permanent photo links.

Finished mine up this evening. Did both the trans mounts and the engine mounts. I'm happy that I installed my driver's side engine mount first. (No preferred order for trans mounts.)

Trans mounts are easiest to do by first taking the nuts off the mounts, then semi detaching the brace that supports the lower portion of the trans mounts. I removed both bolts from the driver's side and loosened the ones on the passenger side. Gained me enough wiggle room to R&R the mounts, but kept me from having to mess with heat shielding and rethreading bolts.

Why do I mention that in a thread that covers engine mounts? Because I couldn't get my passenger side engine mount off the car. The top of the passenger side motor mount bolts to an arm that, in turn, bolts to the engine block. I had unbolted the mounts top and bottom before unbolting the arm. You must support the engine in order to make sure the arm will bolt right up. Another caution is the fourth bolt. It's hidden from sight and is contained in an open arch that reinforces the arm. All of my arm's bolts had 13 mm heads.

Driver's side was pretty normal, but be careful with the jack when lowering it on to the engine mount. They will be misaligned especially if you snug up the lower mount to ensure the alignment pin stays inserted. I also prethreaded the nut on to the upper mount after it was nudged into place. (BTW, it's easier to move the engine to the mount than the other way around.) I could just barely get my fingers in there, but dropping it in from on top sounds like a recipe for frustration.


All times are GMT +1. The time now is 02:59 PM.

vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org

Tutorial powered by GARS 2.1.8m ©2005-2006