Thanks Cooljess! Made this fix 4 years ago following your DIY. Excellent job. Well, it's time to do it again. BTW, Gorilla Glue works excellent to hold the clip posts on the door panel. Only 1 let go from 4 years ago. Fast curing (1 hour) is now available. |
Quote:
|
cooljess i wish i wasnt as infusiatsic impatiant/man to stop and read ur whole steps loooooool i was like yep ok door isnt working both sides and o i see yep door pannal off look o its the sliders k i need new 1s k il get them untill then lets see wats going on btw all ive done is i think looked at a few words lol it goes up and pops out im an idiot im like o its all over the place hmm the ball keeps popping out wtf il bend the arm cause its moving away as it goes up and pops not once did i know there was a horizontal arm on the front holding it in place tomorrow this window is getting fixed no i have read all 11 pages of this post lol i think sites like these and people like all of urselfs are amazing! i just need to stop being impatiant and lazy to read it all haha! need to get the driver side front horizontal arm rewelded on as it fell off well it was like it when i bought the car! ahhh im excited now its like xmas wanna fix it now so bad lol thanks again i really hope its not in the runner so i know its just that proplem :D ooo and the car came with other problems im hoping there is a olace on this site i can be guided too my front fogs dont work and the horn doesnt either and if there is anything on getting the dam locking nut off with out the lock nut would be fantastic as it was not in the car after purchase :( and the wheels are broke buckled unsafe for the road |
hi there again read the post again and gonna read it again in a bit but i wanna just ask cause im loosing my marbles loool i got a pic of the situation the glass will go all the way up without poping the off the runner and closes as should! (never did b4) so im half way there i hope! but on the way down about 7inchs the left runner pops off and the glass at front (car side) runner comes out! :( im twisting all over the place but im scared of breaking it if i keep doing it wrong! so here is the image! really need some help here i just cant work out where its going wrong http://i1338.photobucket.com/albums/...1105-00210.jpg |
So it looks like the glass is popping out of the front runner toward the outside. First, I would recommend making sure that everything else in the system is working properly. If I can decipher your unpunctuated post correctly, it sounds as though one of the arms that raises the glass is damaged - if so, that has to be fixed before you can do anything else. Are the nylon sliders in the window channel, that the spherical joints on the ends of the arms snap into, in good condition? If every other part of the window mechanism seems good, then, yes, you need to bend the rear edge of the front runner inward. - Eric |
You have to close your eyes and try to invision what is happening inside the door when the window comes off track. The forward and rear vertical tracks are supposed to be perfectly parallel with each other. This is what holds the window in the tracks. First you need to determine if the window is coming out of the forward or rear track. Then you need to determine if it's coming out towards the inboard or outboard(towards the interior of the car or towards the exterior). Next you want to imagine which direction that track twisted to allow the window to come out inward or outward, remove the window and twist the vertical track the opposite direction so it's parallel with the other vertical track. |
Quote:
|
sorry that wasnt so clear! ok so as u can see its coming out the front runner but at the same time or wat appears to be the same time the rear lifting arm pops out the nylon sliders were in good condition but has broken the bottom circle now watched it fly past my face :( but i genuinly think that its pushing it out quite hard so even with a good 1 it would still come out! so to me its like its being twisted off but i have oppened the rails wide on the rear so there is actually a bit of room to move its really hard to get to the top front runner to twist it so i oppened it up a lil bit to try eliminate making it go down wrong and twisting it out! hope this makes sence? |
If the window is coming out of the front vertical track, you're only making the problem worse by prying the track open. If the slider is broken, you'll need to replace it. |
Quote:
- Eric |
Quote:
|
if the missing word was slide i have 4 on order :D but till then assumed i could sesolve this issue with wat i have!?? or get very close? so u suggest closing the horizontal tracks front and back leaving about a 6mm gap for the glass? |
Quote:
|
The point is that the two vertical tracks (one of which I imprecisely called the "front runner" in my post above) are what hold the glass in place. Each of these tracks - front and rear - must be clamped tight enough to gently but securely locate the glass and must be at an exactly 90° angle to the glass. If either of these vertical tracks is twisted, even a little bit, to the inside or the outside, then it will spit out the glass when it gets a little torque from the regulator mechanism, through the horizontal track. The horizontal track must be very clean and well greased, the nylon sliders must slide along it easily, and the scissors arms must be bent straight, with the ball ends at exactly 90° to the arms. - Eric |
Great write up cooljess just bought a 318ti and its also from michigan so im seriously considering doing this.. Thanks!! |
All times are GMT +1. The time now is 06:25 PM. |
vBulletin Version 3.8.8
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©1999 - 2024, 318ti.org
Tutorial powered by GARS 2.1.8m ©2005-2006